Resin identification codes, the numbered triangles on plastic packaging, tell recyclers which polymer the bottle is made from. #1 PET, #2 HDPE and #7 OTHER are the codes most cosmetic bottles carry, and they determine whether the pack enters a mainstream recycling stream.
Consumers often treat the chasing-arrows symbol as a promise that the pack will be recycled. Recyclers treat it as a sorting instruction. The resin identification code, first developed by the Society of the Plastics Industry in 1988, identifies the dominant polymer in an item. It does not say whether the item is recyclable in a given region, whether the cap or label is compatible, or whether the pack is made from recycled material. This guide explains the codes most relevant to cosmetic packaging, how they influence recycling value, and how to design a pack so the code on the base matches the stream the pack can actually enter.
Resin codes at a glance
- #1 PET: Polyethylene terephthalate. Clear, strong and widely recycled. Common for serum, lotion and spray bottles. Recyclers value it highly.
- #2 HDPE: High-density polyethylene. Tough, chemical resistant, often opaque. Common for jars, pump bottles and tubes. Widely recycled.
- #7 OTHER: Catch-all for other resins, including PLA, PHA, multilayer and blended materials. Often rejected by mainstream recyclers.
- What the code does: It identifies the main resin so sorting equipment and manual sorters can route the pack. It does not guarantee collection, recycling or end-market demand.
- ShiJin: 1,000+ open molds in PET, HDPE and PETG; MOQ 5,000 units; 15-25 day production. We can mark the correct RIC and help design a mono-material pack that matches the local recycling stream.
What Are Resin Identification Codes?
Resin identification codes, or RICs, are the numbered chasing-arrows symbols found on plastic products. They were introduced by the Society of the Plastics Industry in 1988 to help recyclers identify the dominant polymer in a pack during sorting. The numbers run from one to seven, and each number corresponds to a resin or group of resins.
The symbol is not a recycling guarantee. A bottle marked #1 PET is only recyclable if the local collection system accepts it, the recycler can separate it from other materials, and there is an end market for the recycled flake. A bottle marked #7 OTHER is usually not recyclable in mainstream streams because it contains an uncommon or mixed resin.
The code applies to the dominant material by weight. A PET bottle with a small PP cap and a paper label still carries #1, because the bottle body outweighs the other parts. However, those other parts can still contaminate the recycling process, which is why mono-material design and easy separation matter. Our mono-material design guide explains how to keep the whole pack in one recycling stream.
What Does #1 PET Mean?
PET, or polyethylene terephthalate, is the clear, lightweight resin used for most cosmetic serum, lotion and spray bottles. It has excellent clarity, good barrier properties and high recycling value. Recycled PET, or rPET, is in strong demand for fibre, sheet and new bottle applications, so collected PET usually finds a market.
Most cosmetic PET bottles are clear or lightly tinted. Dark colours and opaque coatings reduce recycling value because they are harder to colour-match in recycled flake. Metalized or metallised finishes can sink in recycling separators and are often removed as contamination. Brands that want a premium look and a #1 recycling story usually choose transparent PET with a printed or labelled decoration rather than a coating.
PETG, a glycol-modified version of PET, carries #7 OTHER because its glycol content changes the melting behaviour. A PETG bottle cannot be mixed with PET in most recycling systems. Our PET vs HDPE vs PETG guide explains why PETG behaves differently on the line and at the recycler.
What Does #2 HDPE Mean?
HDPE, or high-density polyethylene, is the tough, opaque resin used for jars, pump bottles, tubes and caps. It resists impact and many chemicals, which makes it a good choice for products that travel through rough distribution or contain ingredients that stress other resins. Like PET, HDPE is widely collected and recycled into products such as pipe, crates and new bottles.
HDPE is naturally opaque, so colourants are common. Light colours and natural HDPE are easier to recycle into new products than very dark or black HDPE, which near-infrared sorting equipment can miss. Black plastic is a known recycling challenge, and many markets are moving away from it for cosmetic packs that want a recyclability claim.
Caps and closures are often made from a different grade of HDPE or from PP. Because both are polyolefins, they are closer in recycling compatibility than PET caps are to PET bottles, but they still need to be separable by density or manually removed. A jar with an HDPE body and a PP lid can sometimes be recycled together, but a PET bottle with a PP pump almost always needs the pump removed first.
What About #7 OTHER?
#7 OTHER is the catch-all category for plastics that do not fit codes one through six. It includes PLA, PHA, polycarbonate, multilayer barrier materials, and many resin blends. For cosmetic packaging, the most common #7 items are PETG bottles, PLA or PHA biodegradable bottles, and packs with multilayer walls or metallised coatings.
Because #7 covers so many materials, recyclers cannot assume the resin is compatible with any mainstream stream. Most material recovery facilities reject #7 items or downgrade them to mixed-plastic bales with low value. A pack marked #7 is not necessarily unrecyclable in absolute terms, but it is not recyclable through the standard collection systems that handle #1 and #2.
Brands that choose #7 materials should be honest in their messaging. 'Made from recyclable plastic' is misleading if the only available stream is a specialised industrial collection that does not exist in most markets. A better claim is 'designed for industrial composting' for PLA or 'designed for a dedicated recycling stream' for PETG, if that stream is actually accessible to consumers.
How Should You Mark and Design for Recycling?
Put the RIC on the base of the bottle in a size and position that survives filling, labelling and handling. The mark should be moulded or printed directly on the bottle, not only on a removable label, because labels can fall off during sorting. The number should be large enough for optical sorters and manual pickers to read quickly.
Design the pack to match the code. A #1 PET bottle should use a PET or easily separable label, avoid dark colours and coatings, and use a closure that the consumer can remove or that the recycler can separate. A #2 HDPE jar should use an HDPE or PP lid that separates cleanly and a label adhesive that releases in the wash.
Consider the consumer. A pump or dropper with a metal spring cannot be recycled with the bottle, so instructions to remove it help. A label that says 'remove pump before recycling' is more useful than a broad claim that the bottle is recyclable. Our label adhesive guide explains how the wrong glue can turn a recyclable bottle into contamination.
Does the Code Change Recycling Value?
Yes. Recyclers pay more for bales of #1 PET and #2 HDPE because the end markets are mature and the processing is predictable. Mixed bales or bales contaminated with #7 materials sell for less and may be landfilled or incinerated. The code on the bottle is the first signal that determines which bale the pack enters.
Colour and form also affect value. Clear PET is worth more than coloured PET. Natural HDPE is worth more than dark HDPE. Small or odd-shaped packs can slip through sorting screens. A cosmetic brand that wants its pack to be recycled should therefore choose the most common shape, colour and material that fits the brand, not the most unusual one.
At ShiJin we run 1,000+ open molds, MOQ from 5,000 units and 15-25 day production. We can mark the correct RIC, recommend label and closure combinations that match the resin stream, and supply rPET or recycled HDPE where the application allows. Our PCR vs virgin guide explains how recycled content fits with the resin code strategy.
Frequently Asked Questions
What do resin identification codes mean?
Resin identification codes, or RICs, are numbered symbols that identify the dominant plastic in a pack. #1 is PET, #2 is HDPE, and #7 is a catch-all for other resins. They help recyclers sort the material but do not guarantee that the item will be recycled.
Is a bottle marked #1 PET always recyclable?
Not always. The code means the bottle is made from PET, which is widely recyclable, but actual recycling depends on local collection, sorting capability and end-market demand. Caps, labels and coatings can also prevent a PET bottle from being recycled.
Why is PETG marked #7 instead of #1?
PETG is a glycol-modified form of PET. Its melting behaviour is different enough that it cannot be mixed with standard PET in most recycling systems. Because it does not fit #1, it is grouped under #7 OTHER.
Should I mark the cap with a different resin code?
Yes, if the cap is a different resin. Many caps carry their own RIC on the inside. The body code applies to the dominant material by weight, which is usually the bottle or jar, but caps should be marked separately so consumers and recyclers can identify them.
Does black plastic make recycling harder?
Yes. Near-infrared optical sorters often cannot identify black plastic, so it may be rejected or sent to landfill. If recycling is a priority, choose lighter or natural colours for HDPE and avoid black or very dark tints.
Matching bottle options for this topic
Real molds from our library in a comparable material and size class — each product page carries the full spec sheet, neck size, MOQ and lead time.
- PET Cosmetic Bottle 200ml — SKU SJT0225-200
- PET Cosmetic Bottle 250ml — SKU SJT0579-250
- PET Cosmetic Bottle 450ml — SKU SJT0468-450
- PET Cosmetic Bottle 1000ml — SKU SJT0015-1000
Design a bottle that matches the recycling stream
Tell us your target market and sustainability goal. We can recommend the right resin, mark the correct RIC, and design a mono-material pack that fits the local recycling stream, with 1,000+ open molds, MOQ from 5,000 units and 15-25 day lead times.
Browse Mold Library Request a Quote